Wear in particle based CSP systems from particle abrasion and attrition at high temperature Article Swipe
Nipun Goel
,
Tessa Mei-lin Fong
,
John Shingledecker
,
Andrew Russell
,
Michael W. Keller
,
Siamack A. Shirazi
,
Todd Otanicar
·
YOU?
·
· 2021
· Open Access
·
· DOI: https://doi.org/10.2172/1807550
YOU?
·
· 2021
· Open Access
·
· DOI: https://doi.org/10.2172/1807550
High temperature particle-based receivers offer distinct advantages over conventional molten salt receivers due to their ability to achieve temperatures above 700 ºC, direct absorption of solar energy as they fall through a beam of concentrated sunlight, and the relative ease of storage (and retrieval using a secondary working fluid) in insulated storage tanks. The use of particles, however, also raises concerns with material degradation from the flow of hot or cold particles through discharge hoppers or along the inner receiver surfaces and other system components (e.g. tubes, valves etc.), depending on operating mode of the receiver. The flow of particles over surfaces may result in loss of material from abrasive wear, impact erosion from impingement under gravitational fall and particle attrition as particles fall and move on top of each other. In the present study, the performance of candidate materials and particles were evaluated through a series of abrasion erosion and particle attrition experiments at room temperature as well as at 800 °C. Candidate materials were subject to abrasive wear from particles at low particle to material velocities inside a resistance heated kiln, and analyzed for changes in mass and surface morphology using cross-sectional scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) tests. The wear rate for different specimens was noted to be largely driven by the strength of chromia scales built on the specimens from exposure to high temperature. Particle attrition measurements explored the susceptibility of particles to breakdown from particle to particle interaction and the generation of fines from this process. At the low velocities expected in particle based CSP plants, the particles tested exhibited near negligible breakdown. However, changes in the particle hardness at 800 ºC resulted in a significantly higher particle breakdown to sizes <40 microns raising potential environmental concerns. In addition to particle breakdown, it was also noted that the sample had oxides from the stainless steel test setup mixed in with the particles. Similar oxides can be expected to turn up in the utility scale particle based CSP plants as well. The presence of oxide was also noted to affect the solar absorptivity of the mixture compared to a clean initial specimen, potentially resulting in a change in the overall efficiency of the CSP plant.
Related Topics
Concepts
Metadata
- Type
- article
- Language
- en
- Landing Page
- https://doi.org/10.2172/1807550
- OA Status
- green
- Related Works
- 10
- OpenAlex ID
- https://openalex.org/W4390600523
All OpenAlex metadata
Raw OpenAlex JSON
- OpenAlex ID
-
https://openalex.org/W4390600523Canonical identifier for this work in OpenAlex
- DOI
-
https://doi.org/10.2172/1807550Digital Object Identifier
- Title
-
Wear in particle based CSP systems from particle abrasion and attrition at high temperatureWork title
- Type
-
articleOpenAlex work type
- Language
-
enPrimary language
- Publication year
-
2021Year of publication
- Publication date
-
2021-04-19Full publication date if available
- Authors
-
Nipun Goel, Tessa Mei-lin Fong, John Shingledecker, Andrew Russell, Michael W. Keller, Siamack A. Shirazi, Todd OtanicarList of authors in order
- Landing page
-
https://doi.org/10.2172/1807550Publisher landing page
- Open access
-
YesWhether a free full text is available
- OA status
-
greenOpen access status per OpenAlex
- OA URL
-
https://www.osti.gov/biblio/1807550Direct OA link when available
- Concepts
-
Abrasion (mechanical), Particle (ecology), Attrition, Materials science, Particle size, Composite material, Engineering, Geology, Chemical engineering, Orthodontics, Oceanography, MedicineTop concepts (fields/topics) attached by OpenAlex
- Cited by
-
0Total citation count in OpenAlex
- Related works (count)
-
10Other works algorithmically related by OpenAlex
Full payload
| id | https://openalex.org/W4390600523 |
|---|---|
| doi | https://doi.org/10.2172/1807550 |
| ids.doi | https://doi.org/10.2172/1807550 |
| ids.openalex | https://openalex.org/W4390600523 |
| fwci | 0.0 |
| type | article |
| title | Wear in particle based CSP systems from particle abrasion and attrition at high temperature |
| biblio.issue | |
| biblio.volume | |
| biblio.last_page | |
| biblio.first_page | |
| topics[0].id | https://openalex.org/T12099 |
| topics[0].field.id | https://openalex.org/fields/22 |
| topics[0].field.display_name | Engineering |
| topics[0].score | 0.9950000047683716 |
| topics[0].domain.id | https://openalex.org/domains/3 |
| topics[0].domain.display_name | Physical Sciences |
| topics[0].subfield.id | https://openalex.org/subfields/2210 |
| topics[0].subfield.display_name | Mechanical Engineering |
| topics[0].display_name | Advanced materials and composites |
| topics[1].id | https://openalex.org/T12427 |
| topics[1].field.id | https://openalex.org/fields/25 |
| topics[1].field.display_name | Materials Science |
| topics[1].score | 0.9926999807357788 |
| topics[1].domain.id | https://openalex.org/domains/3 |
| topics[1].domain.display_name | Physical Sciences |
| topics[1].subfield.id | https://openalex.org/subfields/2505 |
| topics[1].subfield.display_name | Materials Chemistry |
| topics[1].display_name | Metal Alloys Wear and Properties |
| topics[2].id | https://openalex.org/T12482 |
| topics[2].field.id | https://openalex.org/fields/22 |
| topics[2].field.display_name | Engineering |
| topics[2].score | 0.9851999878883362 |
| topics[2].domain.id | https://openalex.org/domains/3 |
| topics[2].domain.display_name | Physical Sciences |
| topics[2].subfield.id | https://openalex.org/subfields/2205 |
| topics[2].subfield.display_name | Civil and Structural Engineering |
| topics[2].display_name | Tunneling and Rock Mechanics |
| is_xpac | False |
| apc_list | |
| apc_paid | |
| concepts[0].id | https://openalex.org/C118231568 |
| concepts[0].level | 2 |
| concepts[0].score | 0.7959126234054565 |
| concepts[0].wikidata | https://www.wikidata.org/wiki/Q3819233 |
| concepts[0].display_name | Abrasion (mechanical) |
| concepts[1].id | https://openalex.org/C2778517922 |
| concepts[1].level | 2 |
| concepts[1].score | 0.7509339451789856 |
| concepts[1].wikidata | https://www.wikidata.org/wiki/Q7140482 |
| concepts[1].display_name | Particle (ecology) |
| concepts[2].id | https://openalex.org/C2780553607 |
| concepts[2].level | 2 |
| concepts[2].score | 0.7497912049293518 |
| concepts[2].wikidata | https://www.wikidata.org/wiki/Q684868 |
| concepts[2].display_name | Attrition |
| concepts[3].id | https://openalex.org/C192562407 |
| concepts[3].level | 0 |
| concepts[3].score | 0.5115281343460083 |
| concepts[3].wikidata | https://www.wikidata.org/wiki/Q228736 |
| concepts[3].display_name | Materials science |
| concepts[4].id | https://openalex.org/C187530423 |
| concepts[4].level | 2 |
| concepts[4].score | 0.4165581464767456 |
| concepts[4].wikidata | https://www.wikidata.org/wiki/Q7140503 |
| concepts[4].display_name | Particle size |
| concepts[5].id | https://openalex.org/C159985019 |
| concepts[5].level | 1 |
| concepts[5].score | 0.3641873002052307 |
| concepts[5].wikidata | https://www.wikidata.org/wiki/Q181790 |
| concepts[5].display_name | Composite material |
| concepts[6].id | https://openalex.org/C127413603 |
| concepts[6].level | 0 |
| concepts[6].score | 0.11477082967758179 |
| concepts[6].wikidata | https://www.wikidata.org/wiki/Q11023 |
| concepts[6].display_name | Engineering |
| concepts[7].id | https://openalex.org/C127313418 |
| concepts[7].level | 0 |
| concepts[7].score | 0.10363543033599854 |
| concepts[7].wikidata | https://www.wikidata.org/wiki/Q1069 |
| concepts[7].display_name | Geology |
| concepts[8].id | https://openalex.org/C42360764 |
| concepts[8].level | 1 |
| concepts[8].score | 0.06504616141319275 |
| concepts[8].wikidata | https://www.wikidata.org/wiki/Q83588 |
| concepts[8].display_name | Chemical engineering |
| concepts[9].id | https://openalex.org/C29694066 |
| concepts[9].level | 1 |
| concepts[9].score | 0.05516967177391052 |
| concepts[9].wikidata | https://www.wikidata.org/wiki/Q118301 |
| concepts[9].display_name | Orthodontics |
| concepts[10].id | https://openalex.org/C111368507 |
| concepts[10].level | 1 |
| concepts[10].score | 0.0 |
| concepts[10].wikidata | https://www.wikidata.org/wiki/Q43518 |
| concepts[10].display_name | Oceanography |
| concepts[11].id | https://openalex.org/C71924100 |
| concepts[11].level | 0 |
| concepts[11].score | 0.0 |
| concepts[11].wikidata | https://www.wikidata.org/wiki/Q11190 |
| concepts[11].display_name | Medicine |
| keywords[0].id | https://openalex.org/keywords/abrasion |
| keywords[0].score | 0.7959126234054565 |
| keywords[0].display_name | Abrasion (mechanical) |
| keywords[1].id | https://openalex.org/keywords/particle |
| keywords[1].score | 0.7509339451789856 |
| keywords[1].display_name | Particle (ecology) |
| keywords[2].id | https://openalex.org/keywords/attrition |
| keywords[2].score | 0.7497912049293518 |
| keywords[2].display_name | Attrition |
| keywords[3].id | https://openalex.org/keywords/materials-science |
| keywords[3].score | 0.5115281343460083 |
| keywords[3].display_name | Materials science |
| keywords[4].id | https://openalex.org/keywords/particle-size |
| keywords[4].score | 0.4165581464767456 |
| keywords[4].display_name | Particle size |
| keywords[5].id | https://openalex.org/keywords/composite-material |
| keywords[5].score | 0.3641873002052307 |
| keywords[5].display_name | Composite material |
| keywords[6].id | https://openalex.org/keywords/engineering |
| keywords[6].score | 0.11477082967758179 |
| keywords[6].display_name | Engineering |
| keywords[7].id | https://openalex.org/keywords/geology |
| keywords[7].score | 0.10363543033599854 |
| keywords[7].display_name | Geology |
| keywords[8].id | https://openalex.org/keywords/chemical-engineering |
| keywords[8].score | 0.06504616141319275 |
| keywords[8].display_name | Chemical engineering |
| keywords[9].id | https://openalex.org/keywords/orthodontics |
| keywords[9].score | 0.05516967177391052 |
| keywords[9].display_name | Orthodontics |
| language | en |
| locations[0].id | doi:10.2172/1807550 |
| locations[0].is_oa | False |
| locations[0].source | |
| locations[0].license | |
| locations[0].pdf_url | |
| locations[0].version | publishedVersion |
| locations[0].raw_type | proceedings-article |
| locations[0].license_id | |
| locations[0].is_accepted | True |
| locations[0].is_published | True |
| locations[0].raw_source_name | 2021 MRS Spring Meeting & Exhibit |
| locations[0].landing_page_url | https://doi.org/10.2172/1807550 |
| locations[1].id | pmh:oai:osti.gov:1807550 |
| locations[1].is_oa | True |
| locations[1].source.id | https://openalex.org/S4306402487 |
| locations[1].source.issn | |
| locations[1].source.type | repository |
| locations[1].source.is_oa | False |
| locations[1].source.issn_l | |
| locations[1].source.is_core | False |
| locations[1].source.is_in_doaj | False |
| locations[1].source.display_name | OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) |
| locations[1].source.host_organization | https://openalex.org/I139351228 |
| locations[1].source.host_organization_name | Office of Scientific and Technical Information |
| locations[1].source.host_organization_lineage | https://openalex.org/I139351228 |
| locations[1].license | |
| locations[1].pdf_url | |
| locations[1].version | submittedVersion |
| locations[1].raw_type | |
| locations[1].license_id | |
| locations[1].is_accepted | False |
| locations[1].is_published | False |
| locations[1].raw_source_name | |
| locations[1].landing_page_url | https://www.osti.gov/biblio/1807550 |
| indexed_in | crossref |
| authorships[0].author.id | https://openalex.org/A5047170546 |
| authorships[0].author.orcid | https://orcid.org/0000-0001-7599-7405 |
| authorships[0].author.display_name | Nipun Goel |
| authorships[0].countries | US |
| authorships[0].affiliations[0].institution_ids | https://openalex.org/I120156002 |
| authorships[0].affiliations[0].raw_affiliation_string | Boise State Univ., ID (United States) |
| authorships[0].institutions[0].id | https://openalex.org/I120156002 |
| authorships[0].institutions[0].ror | https://ror.org/02e3zdp86 |
| authorships[0].institutions[0].type | education |
| authorships[0].institutions[0].lineage | https://openalex.org/I120156002 |
| authorships[0].institutions[0].country_code | US |
| authorships[0].institutions[0].display_name | Boise State University |
| authorships[0].author_position | first |
| authorships[0].raw_author_name | Nipun Goel |
| authorships[0].is_corresponding | False |
| authorships[0].raw_affiliation_strings | Boise State Univ., ID (United States) |
| authorships[1].author.id | https://openalex.org/A5082204382 |
| authorships[1].author.orcid | https://orcid.org/0000-0002-2790-9957 |
| authorships[1].author.display_name | Tessa Mei-lin Fong |
| authorships[1].countries | US |
| authorships[1].affiliations[0].institution_ids | https://openalex.org/I120156002 |
| authorships[1].affiliations[0].raw_affiliation_string | Boise State Univ., ID (United States) |
| authorships[1].institutions[0].id | https://openalex.org/I120156002 |
| authorships[1].institutions[0].ror | https://ror.org/02e3zdp86 |
| authorships[1].institutions[0].type | education |
| authorships[1].institutions[0].lineage | https://openalex.org/I120156002 |
| authorships[1].institutions[0].country_code | US |
| authorships[1].institutions[0].display_name | Boise State University |
| authorships[1].author_position | middle |
| authorships[1].raw_author_name | Tessa Mei-lin Fong |
| authorships[1].is_corresponding | False |
| authorships[1].raw_affiliation_strings | Boise State Univ., ID (United States) |
| authorships[2].author.id | https://openalex.org/A5034698699 |
| authorships[2].author.orcid | https://orcid.org/0000-0001-5520-3487 |
| authorships[2].author.display_name | John Shingledecker |
| authorships[2].countries | US |
| authorships[2].affiliations[0].institution_ids | https://openalex.org/I1335486098 |
| authorships[2].affiliations[0].raw_affiliation_string | Electric Power Research Inst. (EPRI), Knoxville, TN (United States) |
| authorships[2].institutions[0].id | https://openalex.org/I1335486098 |
| authorships[2].institutions[0].ror | https://ror.org/02dqztz06 |
| authorships[2].institutions[0].type | nonprofit |
| authorships[2].institutions[0].lineage | https://openalex.org/I1335486098 |
| authorships[2].institutions[0].country_code | US |
| authorships[2].institutions[0].display_name | Electric Power Research Institute |
| authorships[2].author_position | middle |
| authorships[2].raw_author_name | John Shingledecker |
| authorships[2].is_corresponding | False |
| authorships[2].raw_affiliation_strings | Electric Power Research Inst. (EPRI), Knoxville, TN (United States) |
| authorships[3].author.id | https://openalex.org/A5006372509 |
| authorships[3].author.orcid | https://orcid.org/0000-0002-9377-8166 |
| authorships[3].author.display_name | Andrew Russell |
| authorships[3].countries | US |
| authorships[3].affiliations[0].institution_ids | https://openalex.org/I120156002 |
| authorships[3].affiliations[0].raw_affiliation_string | Boise State Univ., ID (United States) |
| authorships[3].institutions[0].id | https://openalex.org/I120156002 |
| authorships[3].institutions[0].ror | https://ror.org/02e3zdp86 |
| authorships[3].institutions[0].type | education |
| authorships[3].institutions[0].lineage | https://openalex.org/I120156002 |
| authorships[3].institutions[0].country_code | US |
| authorships[3].institutions[0].display_name | Boise State University |
| authorships[3].author_position | middle |
| authorships[3].raw_author_name | Andrew Russell |
| authorships[3].is_corresponding | False |
| authorships[3].raw_affiliation_strings | Boise State Univ., ID (United States) |
| authorships[4].author.id | https://openalex.org/A5024676846 |
| authorships[4].author.orcid | https://orcid.org/0000-0002-4668-7691 |
| authorships[4].author.display_name | Michael W. Keller |
| authorships[4].countries | US |
| authorships[4].affiliations[0].institution_ids | https://openalex.org/I87208437 |
| authorships[4].affiliations[0].raw_affiliation_string | Univ. of Tulsa, Tulsa, OK (United States) |
| authorships[4].institutions[0].id | https://openalex.org/I87208437 |
| authorships[4].institutions[0].ror | https://ror.org/04wn28048 |
| authorships[4].institutions[0].type | education |
| authorships[4].institutions[0].lineage | https://openalex.org/I87208437 |
| authorships[4].institutions[0].country_code | US |
| authorships[4].institutions[0].display_name | University of Tulsa |
| authorships[4].author_position | middle |
| authorships[4].raw_author_name | Michael Keller |
| authorships[4].is_corresponding | False |
| authorships[4].raw_affiliation_strings | Univ. of Tulsa, Tulsa, OK (United States) |
| authorships[5].author.id | https://openalex.org/A5109526361 |
| authorships[5].author.orcid | |
| authorships[5].author.display_name | Siamack A. Shirazi |
| authorships[5].countries | US |
| authorships[5].affiliations[0].institution_ids | https://openalex.org/I87208437 |
| authorships[5].affiliations[0].raw_affiliation_string | Univ. of Tulsa, Tulsa, OK (United States) |
| authorships[5].institutions[0].id | https://openalex.org/I87208437 |
| authorships[5].institutions[0].ror | https://ror.org/04wn28048 |
| authorships[5].institutions[0].type | education |
| authorships[5].institutions[0].lineage | https://openalex.org/I87208437 |
| authorships[5].institutions[0].country_code | US |
| authorships[5].institutions[0].display_name | University of Tulsa |
| authorships[5].author_position | middle |
| authorships[5].raw_author_name | Siamack Shirazi |
| authorships[5].is_corresponding | False |
| authorships[5].raw_affiliation_strings | Univ. of Tulsa, Tulsa, OK (United States) |
| authorships[6].author.id | https://openalex.org/A5070727043 |
| authorships[6].author.orcid | https://orcid.org/0000-0002-4579-6183 |
| authorships[6].author.display_name | Todd Otanicar |
| authorships[6].countries | US |
| authorships[6].affiliations[0].institution_ids | https://openalex.org/I120156002 |
| authorships[6].affiliations[0].raw_affiliation_string | Boise State Univ., ID (United States) |
| authorships[6].institutions[0].id | https://openalex.org/I120156002 |
| authorships[6].institutions[0].ror | https://ror.org/02e3zdp86 |
| authorships[6].institutions[0].type | education |
| authorships[6].institutions[0].lineage | https://openalex.org/I120156002 |
| authorships[6].institutions[0].country_code | US |
| authorships[6].institutions[0].display_name | Boise State University |
| authorships[6].author_position | last |
| authorships[6].raw_author_name | Todd Otanicar |
| authorships[6].is_corresponding | False |
| authorships[6].raw_affiliation_strings | Boise State Univ., ID (United States) |
| has_content.pdf | False |
| has_content.grobid_xml | False |
| is_paratext | False |
| open_access.is_oa | True |
| open_access.oa_url | https://www.osti.gov/biblio/1807550 |
| open_access.oa_status | green |
| open_access.any_repository_has_fulltext | False |
| created_date | 2025-10-10T00:00:00 |
| display_name | Wear in particle based CSP systems from particle abrasion and attrition at high temperature |
| has_fulltext | False |
| is_retracted | False |
| updated_date | 2025-11-06T03:46:38.306776 |
| primary_topic.id | https://openalex.org/T12099 |
| primary_topic.field.id | https://openalex.org/fields/22 |
| primary_topic.field.display_name | Engineering |
| primary_topic.score | 0.9950000047683716 |
| primary_topic.domain.id | https://openalex.org/domains/3 |
| primary_topic.domain.display_name | Physical Sciences |
| primary_topic.subfield.id | https://openalex.org/subfields/2210 |
| primary_topic.subfield.display_name | Mechanical Engineering |
| primary_topic.display_name | Advanced materials and composites |
| related_works | https://openalex.org/W1969175355, https://openalex.org/W2007101045, https://openalex.org/W4389273703, https://openalex.org/W2056472298, https://openalex.org/W2775846538, https://openalex.org/W2586909830, https://openalex.org/W2116688168, https://openalex.org/W42783218, https://openalex.org/W1563230925, https://openalex.org/W2518391985 |
| cited_by_count | 0 |
| locations_count | 2 |
| best_oa_location.id | pmh:oai:osti.gov:1807550 |
| best_oa_location.is_oa | True |
| best_oa_location.source.id | https://openalex.org/S4306402487 |
| best_oa_location.source.issn | |
| best_oa_location.source.type | repository |
| best_oa_location.source.is_oa | False |
| best_oa_location.source.issn_l | |
| best_oa_location.source.is_core | False |
| best_oa_location.source.is_in_doaj | False |
| best_oa_location.source.display_name | OSTI OAI (U.S. Department of Energy Office of Scientific and Technical Information) |
| best_oa_location.source.host_organization | https://openalex.org/I139351228 |
| best_oa_location.source.host_organization_name | Office of Scientific and Technical Information |
| best_oa_location.source.host_organization_lineage | https://openalex.org/I139351228 |
| best_oa_location.license | |
| best_oa_location.pdf_url | |
| best_oa_location.version | submittedVersion |
| best_oa_location.raw_type | |
| best_oa_location.license_id | |
| best_oa_location.is_accepted | False |
| best_oa_location.is_published | False |
| best_oa_location.raw_source_name | |
| best_oa_location.landing_page_url | https://www.osti.gov/biblio/1807550 |
| primary_location.id | doi:10.2172/1807550 |
| primary_location.is_oa | False |
| primary_location.source | |
| primary_location.license | |
| primary_location.pdf_url | |
| primary_location.version | publishedVersion |
| primary_location.raw_type | proceedings-article |
| primary_location.license_id | |
| primary_location.is_accepted | True |
| primary_location.is_published | True |
| primary_location.raw_source_name | 2021 MRS Spring Meeting & Exhibit |
| primary_location.landing_page_url | https://doi.org/10.2172/1807550 |
| publication_date | 2021-04-19 |
| publication_year | 2021 |
| referenced_works_count | 0 |
| abstract_inverted_index.a | 31, 45, 145, 179, 283, 356, 363 |
| abstract_inverted_index.At | 255 |
| abstract_inverted_index.In | 131, 296 |
| abstract_inverted_index.as | 27, 121, 157, 159, 337 |
| abstract_inverted_index.at | 154, 160, 172, 278 |
| abstract_inverted_index.be | 214, 324 |
| abstract_inverted_index.by | 217 |
| abstract_inverted_index.in | 49, 104, 187, 260, 274, 282, 317, 329, 362, 365 |
| abstract_inverted_index.it | 301 |
| abstract_inverted_index.of | 24, 33, 40, 55, 67, 93, 98, 106, 128, 137, 147, 220, 238, 250, 341, 351, 369 |
| abstract_inverted_index.on | 90, 126, 224 |
| abstract_inverted_index.or | 69, 75 |
| abstract_inverted_index.to | 13, 16, 167, 175, 213, 229, 240, 244, 288, 298, 326, 346, 355 |
| abstract_inverted_index.up | 328 |
| abstract_inverted_index.700 | 20 |
| abstract_inverted_index.800 | 161, 279 |
| abstract_inverted_index.CSP | 263, 335, 371 |
| abstract_inverted_index.The | 53, 96, 205, 339 |
| abstract_inverted_index.and | 36, 81, 118, 124, 140, 150, 183, 189, 198, 247 |
| abstract_inverted_index.can | 323 |
| abstract_inverted_index.due | 12 |
| abstract_inverted_index.for | 185, 208 |
| abstract_inverted_index.had | 308 |
| abstract_inverted_index.hot | 68 |
| abstract_inverted_index.low | 173, 257 |
| abstract_inverted_index.may | 102 |
| abstract_inverted_index.the | 37, 65, 77, 94, 132, 135, 218, 225, 236, 248, 256, 265, 275, 306, 311, 319, 330, 348, 352, 366, 370 |
| abstract_inverted_index.top | 127 |
| abstract_inverted_index.use | 54 |
| abstract_inverted_index.was | 211, 302, 343 |
| abstract_inverted_index.ºC | 280 |
| abstract_inverted_index.(and | 42 |
| abstract_inverted_index.High | 0 |
| abstract_inverted_index.also | 58, 303, 344 |
| abstract_inverted_index.beam | 32 |
| abstract_inverted_index.cold | 70 |
| abstract_inverted_index.each | 129 |
| abstract_inverted_index.ease | 39 |
| abstract_inverted_index.fall | 29, 117, 123 |
| abstract_inverted_index.flow | 66, 97 |
| abstract_inverted_index.from | 64, 108, 113, 170, 227, 242, 252, 310 |
| abstract_inverted_index.high | 230 |
| abstract_inverted_index.loss | 105 |
| abstract_inverted_index.mass | 188 |
| abstract_inverted_index.mode | 92 |
| abstract_inverted_index.move | 125 |
| abstract_inverted_index.near | 269 |
| abstract_inverted_index.over | 7, 100 |
| abstract_inverted_index.rate | 207 |
| abstract_inverted_index.room | 155 |
| abstract_inverted_index.salt | 10 |
| abstract_inverted_index.test | 314 |
| abstract_inverted_index.that | 305 |
| abstract_inverted_index.they | 28 |
| abstract_inverted_index.this | 253 |
| abstract_inverted_index.turn | 327 |
| abstract_inverted_index.wear | 169, 206 |
| abstract_inverted_index.well | 158 |
| abstract_inverted_index.were | 142, 165 |
| abstract_inverted_index.with | 61, 318 |
| abstract_inverted_index.°C. | 162 |
| abstract_inverted_index.ºC, | 21 |
| abstract_inverted_index.(EDS) | 203 |
| abstract_inverted_index.(SEM) | 197 |
| abstract_inverted_index.(e.g. | 85 |
| abstract_inverted_index.above | 19 |
| abstract_inverted_index.along | 76 |
| abstract_inverted_index.based | 262, 334 |
| abstract_inverted_index.built | 223 |
| abstract_inverted_index.clean | 357 |
| abstract_inverted_index.fines | 251 |
| abstract_inverted_index.inner | 78 |
| abstract_inverted_index.kiln, | 182 |
| abstract_inverted_index.mixed | 316 |
| abstract_inverted_index.noted | 212, 304, 345 |
| abstract_inverted_index.offer | 4 |
| abstract_inverted_index.other | 82 |
| abstract_inverted_index.oxide | 342 |
| abstract_inverted_index.scale | 332 |
| abstract_inverted_index.setup | 315 |
| abstract_inverted_index.sizes | 289 |
| abstract_inverted_index.solar | 25, 349 |
| abstract_inverted_index.steel | 313 |
| abstract_inverted_index.their | 14 |
| abstract_inverted_index.under | 115 |
| abstract_inverted_index.using | 44, 192 |
| abstract_inverted_index.wear, | 110 |
| abstract_inverted_index.well. | 338 |
| abstract_inverted_index.x-ray | 201 |
| abstract_inverted_index.<40 | 290 |
| abstract_inverted_index.affect | 347 |
| abstract_inverted_index.change | 364 |
| abstract_inverted_index.direct | 22 |
| abstract_inverted_index.driven | 216 |
| abstract_inverted_index.energy | 26, 199 |
| abstract_inverted_index.etc.), | 88 |
| abstract_inverted_index.fluid) | 48 |
| abstract_inverted_index.heated | 181 |
| abstract_inverted_index.higher | 285 |
| abstract_inverted_index.impact | 111 |
| abstract_inverted_index.inside | 178 |
| abstract_inverted_index.molten | 9 |
| abstract_inverted_index.other. | 130 |
| abstract_inverted_index.oxides | 309, 322 |
| abstract_inverted_index.plant. | 372 |
| abstract_inverted_index.plants | 336 |
| abstract_inverted_index.raises | 59 |
| abstract_inverted_index.result | 103 |
| abstract_inverted_index.sample | 307 |
| abstract_inverted_index.scales | 222 |
| abstract_inverted_index.series | 146 |
| abstract_inverted_index.study, | 134 |
| abstract_inverted_index.system | 83 |
| abstract_inverted_index.tanks. | 52 |
| abstract_inverted_index.tested | 267 |
| abstract_inverted_index.tests. | 204 |
| abstract_inverted_index.tubes, | 86 |
| abstract_inverted_index.valves | 87 |
| abstract_inverted_index.Similar | 321 |
| abstract_inverted_index.ability | 15 |
| abstract_inverted_index.achieve | 17 |
| abstract_inverted_index.changes | 186, 273 |
| abstract_inverted_index.chromia | 221 |
| abstract_inverted_index.erosion | 112, 149 |
| abstract_inverted_index.hoppers | 74 |
| abstract_inverted_index.initial | 358 |
| abstract_inverted_index.largely | 215 |
| abstract_inverted_index.microns | 291 |
| abstract_inverted_index.mixture | 353 |
| abstract_inverted_index.overall | 367 |
| abstract_inverted_index.plants, | 264 |
| abstract_inverted_index.present | 133 |
| abstract_inverted_index.raising | 292 |
| abstract_inverted_index.storage | 41, 51 |
| abstract_inverted_index.subject | 166 |
| abstract_inverted_index.surface | 190 |
| abstract_inverted_index.through | 30, 72, 144 |
| abstract_inverted_index.utility | 331 |
| abstract_inverted_index.working | 47 |
| abstract_inverted_index.However, | 272 |
| abstract_inverted_index.Particle | 232 |
| abstract_inverted_index.abrasion | 148 |
| abstract_inverted_index.abrasive | 109, 168 |
| abstract_inverted_index.addition | 297 |
| abstract_inverted_index.analyzed | 184 |
| abstract_inverted_index.compared | 354 |
| abstract_inverted_index.concerns | 60 |
| abstract_inverted_index.distinct | 5 |
| abstract_inverted_index.electron | 195 |
| abstract_inverted_index.expected | 259, 325 |
| abstract_inverted_index.explored | 235 |
| abstract_inverted_index.exposure | 228 |
| abstract_inverted_index.hardness | 277 |
| abstract_inverted_index.however, | 57 |
| abstract_inverted_index.material | 62, 107, 176 |
| abstract_inverted_index.particle | 119, 151, 174, 243, 245, 261, 276, 286, 299, 333 |
| abstract_inverted_index.presence | 340 |
| abstract_inverted_index.process. | 254 |
| abstract_inverted_index.receiver | 79 |
| abstract_inverted_index.relative | 38 |
| abstract_inverted_index.resulted | 281 |
| abstract_inverted_index.scanning | 194 |
| abstract_inverted_index.strength | 219 |
| abstract_inverted_index.surfaces | 80, 101 |
| abstract_inverted_index.Candidate | 163 |
| abstract_inverted_index.attrition | 120, 152, 233 |
| abstract_inverted_index.breakdown | 241, 287 |
| abstract_inverted_index.candidate | 138 |
| abstract_inverted_index.concerns. | 295 |
| abstract_inverted_index.depending | 89 |
| abstract_inverted_index.different | 209 |
| abstract_inverted_index.discharge | 73 |
| abstract_inverted_index.evaluated | 143 |
| abstract_inverted_index.exhibited | 268 |
| abstract_inverted_index.insulated | 50 |
| abstract_inverted_index.materials | 139, 164 |
| abstract_inverted_index.operating | 91 |
| abstract_inverted_index.particles | 71, 99, 122, 141, 171, 239, 266 |
| abstract_inverted_index.potential | 293 |
| abstract_inverted_index.receiver. | 95 |
| abstract_inverted_index.receivers | 3, 11 |
| abstract_inverted_index.resulting | 361 |
| abstract_inverted_index.retrieval | 43 |
| abstract_inverted_index.secondary | 46 |
| abstract_inverted_index.specimen, | 359 |
| abstract_inverted_index.specimens | 210, 226 |
| abstract_inverted_index.stainless | 312 |
| abstract_inverted_index.sunlight, | 35 |
| abstract_inverted_index.absorption | 23 |
| abstract_inverted_index.advantages | 6 |
| abstract_inverted_index.breakdown, | 300 |
| abstract_inverted_index.breakdown. | 271 |
| abstract_inverted_index.components | 84 |
| abstract_inverted_index.dispersive | 200 |
| abstract_inverted_index.efficiency | 368 |
| abstract_inverted_index.generation | 249 |
| abstract_inverted_index.microscopy | 196 |
| abstract_inverted_index.morphology | 191 |
| abstract_inverted_index.negligible | 270 |
| abstract_inverted_index.particles, | 56 |
| abstract_inverted_index.particles. | 320 |
| abstract_inverted_index.resistance | 180 |
| abstract_inverted_index.velocities | 177, 258 |
| abstract_inverted_index.degradation | 63 |
| abstract_inverted_index.experiments | 153 |
| abstract_inverted_index.impingement | 114 |
| abstract_inverted_index.interaction | 246 |
| abstract_inverted_index.performance | 136 |
| abstract_inverted_index.potentially | 360 |
| abstract_inverted_index.temperature | 1, 156 |
| abstract_inverted_index.absorptivity | 350 |
| abstract_inverted_index.concentrated | 34 |
| abstract_inverted_index.conventional | 8 |
| abstract_inverted_index.measurements | 234 |
| abstract_inverted_index.spectroscopy | 202 |
| abstract_inverted_index.temperature. | 231 |
| abstract_inverted_index.temperatures | 18 |
| abstract_inverted_index.environmental | 294 |
| abstract_inverted_index.gravitational | 116 |
| abstract_inverted_index.significantly | 284 |
| abstract_inverted_index.particle-based | 2 |
| abstract_inverted_index.susceptibility | 237 |
| abstract_inverted_index.cross-sectional | 193 |
| cited_by_percentile_year | |
| countries_distinct_count | 1 |
| institutions_distinct_count | 7 |
| citation_normalized_percentile.value | 0.27125948 |
| citation_normalized_percentile.is_in_top_1_percent | False |
| citation_normalized_percentile.is_in_top_10_percent | False |