J. Berghold
YOU?
Author Swipe
View article: Results of IEC 62804 Draft Round Robin Testing (Presentation)
Results of IEC 62804 Draft Round Robin Testing (Presentation) Open
Three crystalline silicon module designs were distributed in five replicas each to five laboratories for testing according to the IEC 62804 (Committee Draft) system voltage durability qualification test for crystalline silicon photovoltaic…
View article: Advanced PV Module Hot Spot Characterisation
Advanced PV Module Hot Spot Characterisation Open
Photovoltaic modules are the key component of any solar power plants. Their long-term performance and availability are responsible for the electrical yield and thus for the profitability of the power plant. To minimise the failure risk, ex…
View article: Shadowing Investigations on Thin Film Modules
Shadowing Investigations on Thin Film Modules Open
PV modules in solar plants are exposed to changing shading conditions. Due to partial module shading, cells are forced to operate in their reverse bias, which potentially leads to hot spots. In extreme situations, the extraordinarily high …
View article: Regeneration of Potential Induced Degradation Affected Modules
Regeneration of Potential Induced Degradation Affected Modules Open
There are certain regeneration methods to recover photovoltaic modules which are affected with potential-induced degradation (PID) in a PV-plant. The aim of these investigations is to compare the effectiveness of the solutions of two well-…
View article: Outdoor Electroluminescence Imaging of Crystalline Photovoltaic Modules: Comparative Study between Manual Ground-Level Inspections and Drone-Based Aerial Surveys
Outdoor Electroluminescence Imaging of Crystalline Photovoltaic Modules: Comparative Study between Manual Ground-Level Inspections and Drone-Based Aerial Surveys Open
The electroluminescence (EL) scan is a powerful method to detect solar cells or modules with various defects. The electroluminescence measurement is used by default already in most cell and module production although an international stand…
View article: Indoor and Outdoor Characterization of Innovative Colored BIPV Modules for Façade Application
Indoor and Outdoor Characterization of Innovative Colored BIPV Modules for Façade Application Open
The integration of photovoltaic technologies in buildings is considered as promising way to profit by renewable energies in the built environment, with many advantages. Nevertheless, dealing with PV in architecture is still a challenge for…
View article: Investigation on the Impact of Module Cleaning on the Antireflection Coating
Investigation on the Impact of Module Cleaning on the Antireflection Coating Open
Soiling can cause strong losses in the performance of PV modules, especially in regions with high dust loads like deserts. Therefore, the modules are periodically cleaned in many cases, which can damage the surface of the modules, especial…
View article: Hot-Spot Measurements on Crystalline Silicon Solar Cells with Different Reverse Current Characteristic
Hot-Spot Measurements on Crystalline Silicon Solar Cells with Different Reverse Current Characteristic Open
Hot spots of crystalline silicon solar cells are a major failure mode for solar modules. Consecutive on our last year’s investigation where we showed that a comparison of (i) a simple hot spot test on bare cells in the dark to (ii) a hot s…
View article: Energy Yield Estimation of Monofacial and Bifacial Solar Modules
Energy Yield Estimation of Monofacial and Bifacial Solar Modules Open
Monofacial and bifacial solar modules featuring diverse characteristics were produced and measured indoor under standard test conditions (STC). They were installed in the desert in El Gouna, Egypt, where their IV curves were recorded conti…
View article: Thermal Stress Analysis at Encapsulation and Backsheet Materials for PV-Modules
Thermal Stress Analysis at Encapsulation and Backsheet Materials for PV-Modules Open
Infrared imaging is a powerful method to identify and to analyze solar cells or modules with relatively higher temperatures during flied inspections. Higher temperature values can be attributed to cell mismatches, shadowing or isolated fra…
View article: Improvement of a Prediction Model for Potential Induced Degradation by Better Understanding the Regeneration Mechanism
Improvement of a Prediction Model for Potential Induced Degradation by Better Understanding the Regeneration Mechanism Open
This paper is the continuation of the work presented at the EUPVEC 2013 and 2014 [1, 2]. It will present the further developed PID simulation model. The potential-induced-degradation (PID) effect can be described mainly by two parameters. …
View article: Reflectance Measurements for Testing the Effect of Module Cleaning on the Glass Surface
Reflectance Measurements for Testing the Effect of Module Cleaning on the Glass Surface Open
In the last years, because of the higher irradiation, an increase of installed PV systems situated close to the equator line could be observed. As these regions are often characterized by an arid climate, sand and dust deposition on the so…