Mohammad Habibi Parsa
YOU?
Author Swipe
View article: Achieving Fine‐Grained Microstructure in Low‐Alloy Steel: A Study on Static Recrystallization Using Experimental and Simulation Approaches
Achieving Fine‐Grained Microstructure in Low‐Alloy Steel: A Study on Static Recrystallization Using Experimental and Simulation Approaches Open
Recrystallization kinetics and microstructure evolution of low‐alloy steel with the capability to take part in the transformation‐induced plasticity phenomenon are investigated through experimentations and cellular automata (CA) simulation…
View article: Constitutive analysis of Cu-DHP alloy during hot compression
Constitutive analysis of Cu-DHP alloy during hot compression Open
The hot deformation behavior of the deoxidized high-phosphorus copper (Cu-DHP) was investigated during compressive deformation at a wide deformation temperature range of 200 to 1000?C and strain rates ranging from 0.0005 to 0.4 \mathrm{s}^…
View article: Characterizing pearlite transformation in an API X60 pipeline steel through phase-field modeling and experimental validation
Characterizing pearlite transformation in an API X60 pipeline steel through phase-field modeling and experimental validation Open
This study explores the microstructural characterization of pearlite phase transformation in high-strength low-alloy API X60 steel, which is used in pipelines. Understanding the formation, phase percentages, and morphology of the pearlitic…
View article: Phase transformation kinetics of high-carbon steel during continuous heating
Phase transformation kinetics of high-carbon steel during continuous heating Open
Effects of heating temperature, heating rate, and holding time on the austenitization process of near-eutectoid high-carbon steel have been investigated. The dilatometric tests were carried out at different heating rates of 1–100 °C/Sec. T…
View article: A study on microstructure development and mechanical properties of pure copper subjected to severe plastic deformation by the ECAP-Conform process
A study on microstructure development and mechanical properties of pure copper subjected to severe plastic deformation by the ECAP-Conform process Open
View article: A dislocation assisted self-consistent constitutive model for the high-temperature deformation of particulate metal-matrix composite
A dislocation assisted self-consistent constitutive model for the high-temperature deformation of particulate metal-matrix composite Open
A dislocation assisted self-consistent model based on Tandon and Weng approach and Bergstrom dynamic recovery model for particulate-reinforced composites has been extended to consider the matrix evolution during high-temperature deformatio…
View article: Texture development during hot deformation of Al/Mg alloy reinforced with ceramic particles
Texture development during hot deformation of Al/Mg alloy reinforced with ceramic particles Open
View article: Microstructural investigation of Al-Mg/B4C composite deformed at elevated temperature
Microstructural investigation of Al-Mg/B4C composite deformed at elevated temperature Open
View article: Dynamic deformation response of Al-Mg and Al-Mg/B4C composite at elevated temperatures
Dynamic deformation response of Al-Mg and Al-Mg/B4C composite at elevated temperatures Open
View article: Contents: steel research int. 7/2016
Contents: steel research int. 7/2016 Open
Cover Photo
View article: Grain Refinement Efficiency of Multi-Axial Incremental Forging and Shearing: A Crystal Plasticity Analysis
Grain Refinement Efficiency of Multi-Axial Incremental Forging and Shearing: A Crystal Plasticity Analysis Open
Severe plastic deformation is a technical method to produce functional material with special properties such as high strength and specific physical properties. Selection of an efficient severe plastic deformation for grain refinement is a …
View article: Modification of As-cast Al-Mg/B4C composite by addition of Zr
Modification of As-cast Al-Mg/B4C composite by addition of Zr Open
View article: Microstructural Evolution of Roll Bonded Al-Clad Stainless Steel Sheets at Elevated Temperatures
Microstructural Evolution of Roll Bonded Al-Clad Stainless Steel Sheets at Elevated Temperatures Open
The cold roll bonding of Al on AISI 304L stainless steel was carried out to fabricate the Al/304L/Al clad sheet composites. The maximum bond strength of 20 N/mm was acquired just by 38% reduction, for which the tearing of the aluminum shee…
View article: Unraveling the Effect of Homogenization Treatment on Decomposition of Austenite and Mechanical Properties of Low‐Alloyed TRIP Steel
Unraveling the Effect of Homogenization Treatment on Decomposition of Austenite and Mechanical Properties of Low‐Alloyed TRIP Steel Open
The homogenization treatment is shown to have profound effects on the decomposition of austenite, suppression of microstructural banding, and work‐hardening capacity of transformation‐induced plasticity (TRIP) steels. Due to the similarity…
View article: Martensite phase reversion-induced nano/ ultrafine grained AISI 304L stainless steel with magnificent mechanical properties
Martensite phase reversion-induced nano/ ultrafine grained AISI 304L stainless steel with magnificent mechanical properties Open
Austenitic stainless steels are extensively used in various applications requiring good corrosion resistance and formability. In the current study, the formation of nano/ ultrafine grained austenitic microstructure in a microalloyed AISI 3…
View article: The Effect of Strain Rate on Ultra-fine Grained Structure of Cold Drawn 304L Stainless Steel Wires
The Effect of Strain Rate on Ultra-fine Grained Structure of Cold Drawn 304L Stainless Steel Wires Open
The effect of strain rate on nano structured and ultra-fine grained microstructure in austenitic stainless steel AISI 304L was investigated during cold wire drawing process. This process was used to produce strain induced martensite transf…