Sivarao Subramonian
YOU?
Author Swipe
View article: Development and Characterization of Electrical Discharge Coating Electrode Through Powder Metallurgy Process
Development and Characterization of Electrical Discharge Coating Electrode Through Powder Metallurgy Process Open
In this study, copper electrodes for electrical discharge coating (EDC) application were fabricated by using the powder metallurgy (PM) process. The effect of different compaction loads (ranging from 3 to 5 tons) and sintering temperatures…
View article: Microstructural investigation and mechanical properties of Al<sub>2</sub>O<sub>3</sub>-MWCNTs reinforced aluminium composite
Microstructural investigation and mechanical properties of Al<sub>2</sub>O<sub>3</sub>-MWCNTs reinforced aluminium composite Open
Hybrid reinforcement of metal matrix composites (MMCs), particularly those based on aluminum, is widely recognized for resulting in excellent mechanical properties, such as high strength-to-weight ratio, enhanced wear resistance, and super…
View article: Effect of Graphene Addition on Microstructure and Mechanical Properties of Cast Aluminium Alloy Composite
Effect of Graphene Addition on Microstructure and Mechanical Properties of Cast Aluminium Alloy Composite Open
Aluminium-reinforced metal matrix composites (Al-MMCs) are highly desirable because of their low density, excellent corrosion resistance, high thermal and electrical conductivity, high strength, and stiffness. This research intends to impr…
View article: Influence of Graphene on the Microstructure and Mechanical Properties of Aluminium Matrix Composite
Influence of Graphene on the Microstructure and Mechanical Properties of Aluminium Matrix Composite Open
The constraints of conventional aluminum alloys have prompted the investigation of strengthening substances such as carbon nanotubes and graphene fillers. The improved composite exhibits suitability for applications in the automotive and a…
View article: Artificial Neural Network Performance Modeling and Evaluation of Additive Manufacturing 3D Printed Parts
Artificial Neural Network Performance Modeling and Evaluation of Additive Manufacturing 3D Printed Parts Open
This research article presents a comprehensive study on the performance modeling of 3D printed parts using Artificial Neural Networks (ANNs). The aim of this study is to optimize the mechanical properties of 3D printed components through a…
View article: Enhancing Heat Transfer in Compact Automotive Engines using Hybrid Nano Coolants
Enhancing Heat Transfer in Compact Automotive Engines using Hybrid Nano Coolants Open
This research aimed to compare the performance of a reduced-scale automotive radiator using single nano coolant (CNC and CuO) and its hybrid nano coolant (CNC and CuO nanoparticles) to enhance heat transmission. Three ratios of 70:30, 80:2…
View article: Python programming predictions of Thermal Behavioral Aspects of Orange Peel and Coconut-Coir Reinforced Epoxy Composites
Python programming predictions of Thermal Behavioral Aspects of Orange Peel and Coconut-Coir Reinforced Epoxy Composites Open
Using a hand lay-up approach, both orange peel and coconut coir fibres are used in particulate form with an epoxy matrix to create partly green biodegradable composites. The findings indicate great opportunities for employing these natural…
View article: A Comprehensive Review on Graphene Nanoparticles: Preparation, Properties, and Applications
A Comprehensive Review on Graphene Nanoparticles: Preparation, Properties, and Applications Open
Graphene, with its amazing prospects and nonpareil aspects, has enticed scientists and researchers all over the globe in a significant fashion. Graphene, the super material, endlessly demonstrates some of the substantial, as well as desire…
View article: Design and Development of Autonomous Pesticide Sprayer Robot for Fertigation Farm
Design and Development of Autonomous Pesticide Sprayer Robot for Fertigation Farm Open
The management of pest insects is the critical component of agricultural production especially in the fertigation based farm. Although the fertigation farm in Malaysia has advantages in the fertilization and irrigation management system, i…
View article: Optimization of Surface Roughness of D2 Steels in WEDM using ANN Technique
Optimization of Surface Roughness of D2 Steels in WEDM using ANN Technique Open
Attempt has been made to investigate the experimental process and surface roughness (SR) optimization of cold working (high carbon and high chromium) hard die steel (D2) during wire electrical discharge machining processes (WEDM). It is ve…
View article: Performance Analysis of Acceleration Sensor for Movement Detection in Vehicle Security System
Performance Analysis of Acceleration Sensor for Movement Detection in Vehicle Security System Open
The vehicle security system is a critical part of an entire car system in order to prevent unauthorized access into the car. As the statistic has shown that the number of cases of the private car being stolen is increasing and the recovery…
View article: MATHEMATICAL MODELLING AND CONCEPTUAL DESIGN OF NOVEL AUTOMATIC TYRE INFLATING SYSTEM
MATHEMATICAL MODELLING AND CONCEPTUAL DESIGN OF NOVEL AUTOMATIC TYRE INFLATING SYSTEM Open
Pneumatic tyres release 10-15 kPa of air pressure every month requires regular topping up. Vehicles run with improper tyre pressure has been identified as one of the primary factors which leads into major and catastrophic road accidents du…
View article: Interchangeable core and cavity plates for two-plate family injection mould
Interchangeable core and cavity plates for two-plate family injection mould Open
This study modified a two-plate family plastic injection mould to become interchangeable by changing the core and cavity plates using an existing mould base. The plastic parts produced in the modified two-plate family plastic injection mou…
View article: PRELIMINARY STUDY ON THE SOUND ABSORPTION BEHAVIOR OF SPENT TEA LEAVES FILLED WITH NATURAL RUBBER LATEX BINDER
PRELIMINARY STUDY ON THE SOUND ABSORPTION BEHAVIOR OF SPENT TEA LEAVES FILLED WITH NATURAL RUBBER LATEX BINDER Open
Nowadays, sound control has been regarded as one of the important requirements for human comfort. For an instance, control of room acoustic enables the room to achieve a good auditive environment for effective speech deliverance and presen…
View article: Effect of fiber loading on the mechanical properties of bagasse fiber–reinforced polypropylene composites
Effect of fiber loading on the mechanical properties of bagasse fiber–reinforced polypropylene composites Open
It is evident that sugarcane/bagasse is a highly potential natural composite fiber. In this study, the correlation of composition fiber amount to the mechanical strength was presented. Bagasse was treated with alkali and then reinforced in…
View article: A knowledge-based architecture framework of design for assemble system (DAEx)
A knowledge-based architecture framework of design for assemble system (DAEx) Open
Malaysian manufacturing sector has played an important role to boost up the economy at the domestic market. Today, the Malaysian manufacturing sector has facing the challenges that the manufacturing industry need to stay competitive to com…
View article: Conceptual design and implementation of electronic spectacle based obstacle detection for visually impaired persons
Conceptual design and implementation of electronic spectacle based obstacle detection for visually impaired persons Open
In this paper, the design and implementation of a spectacle based obstacle detection system is described. The usage of spectacle based obstacle detection system would help the visually impaired person to scan the surrounding especially at …
View article: A Rule-Based Industrial Boiler Selection System
A Rule-Based Industrial Boiler Selection System Open
Boiler is a device used for generating the steam for power generation, process use or heating, and hot water for heating purposes. Steam boiler consists of the containing vessel and convection heating surfaces only, whereas a steam generat…
View article: Micro-drilling of silicon wafer by industrial CO2 laser
Micro-drilling of silicon wafer by industrial CO2 laser Open
Laser micromachining is currently used in the MEMS production to replace the traditional etching process which consumes longer time to complete. The objective of this study is to investigate the drilling capability of industrial CO2 laser …
View article: AIR PERMEABILITY INVESTIGATION TOWARDS AUTOMOTIVE TYRE PRESSURE SUSTAINABILITY AND LIFE SAVING
AIR PERMEABILITY INVESTIGATION TOWARDS AUTOMOTIVE TYRE PRESSURE SUSTAINABILITY AND LIFE SAVING Open
One of the main reasons for major road accidents which often lead into loss of life's is the catastrophic
\ntyre failure caused by vehicles running with improper tyre pressure. The phenomena where tyre loses
\npressure naturally and contra…