Explanipedia

Backward Brillouin three-parameter sensing simulation based on multicore optical fibers Open

Donghe Sheng, Yunlong Chang, Zhe Han, Yuanyuan Liu, Huiping Tian · 2025

Conventional distributed Brillouin optical fiber sensors, whether theoretically modeled or experimentally implemented, provide simultaneous access to only two physical parameters at most, typically limited to either curvature or temperatur…

Study on the arc behavior of laminar plasma arc welding Open

Honglei Zhao, Siyu Zhang, Xianglong Yu, Yiwen Li, Junyan Miao , et al. · 2025

Uncovering phenolic profiles of different forms in safflower seeds and their antioxidant capacity, and biological activity Open

Yunlong Chang, Nai‐Chang Hou, Jia‐Lin Fei, Zhi Qin, Yulong Niu , et al. · 2025

In this study, free, soluble bound (glycosylated, esterified), and insoluble‐bound phenolic compounds from safflower seeds were identified and quantified by UPLC‐MS/MS. The four phenolic fractions were assessed for their antioxidant capaci…

Effect of heat pretreatment of safflower seeds on quality and polyphenol composition of extracted oil Open

Rui Wang, Nai‐Chang Hou, Zi-Meng Chen, Yitong Liu, Zhi Qin , et al. · 2025

Performance analysis of parallel flow heat exchanger based on water and R134a Open

Hao Cheng, Yingzi Li, Yunlong Chang, Cheng Quan, Weixing Yuan · 2025

This study constructs and validates a heat transfer model of a PFHE applied in data center cabinet cooling systems, using water and R134a as working fluids. By comparing with experimental data, the specific impacts of the two working fluid…

Metabolomics analysis of germinated sesame (Sesamum indicum L.) seeds: Possibility of incorporating short-term germination treatments into the sesame production process Open

Yunlong Chang, Zhi Qin, Zifan Zhang, Yulong Niu, Jiarui Li , et al. · 2024

Microstructure and Mechanical Properties of a Weld Seam from Magnetron High-Current CO2 Welding Open

Jiashi Miao, Yiwen Li, Bowen Ren, Honglei Zhao, Siyu Zhang , et al. · 2024

External magnetic field (EMF)-assisted high-current CO2 welding is beneficial for improving the large spatter and poor performance of the welding heat-affected zone for mild steels under high-current welding specifications. In this paper, …

Numerical and experimental study of TIG welding arc in high frequency longitudinal magnetic field Open

Y. Liu, Hongfa Ding, Jian Luo, Dampilon Bair, Xiaolong Xu , et al. · 2024

The phenomenon of arc compression in TIG welding with high-frequency longitudinal magnetic field (HF-LMF) has been observed. However, its mechanism remains unclear, and there is a lack of numerical investigation. This work presents a two-d…

Research status of high efficiency deep penetration welding of medium-thick plate titanium alloy: A review Open

Zhihai Dong, Ye Tian, Long Zhang, Tong Jiang, Dafeng Wang , et al. · 2024

Composition of sesame hull oil and its effects on flavour and quality of sesame oil Open

Rui Wang, Bing‐Xin Guo, Xiaoyu Li, Jin‐Qiao Peng, Yitong Liu , et al. · 2024

In this study, sesame hull oil (SHO) was extracted to characterise its composition. SHO was heated to determine the volatiles and their effect on the quality of cold-pressed dehulled sesame oil (SO). Seventeen fatty acids, four lignans (10…

Influence of magnetic head structure and parameters on the axial magnetic field hybrid TIG welding Open

Hong Wu, Yunlong Chang, Chenhe Chang · 2024

Through the analysis of the magnetic field around the arc, the feasibility of controlling the arc shape and performance by the external axial magnetic field is clarified. Combined with the derived mathematical expression of the alternating…

Design and analysis of magnetostrictive two-dimensional kinetic energy harvester Open

Huifang Liu, Xiaoyan Tong, Xingwei Sun, Wenguo Wang, Su Liang , et al. · 2024

Conventional energy harvesters often require high ambient vibration frequencies and can only capture vibration energy in a single direction. To address these issues, this paper designs a magnetostrictive two-dimensional kinetic energy harv…

Fabrication and Characteristic Study of Flexible Magnetostrictive Fiber Ribbon Based on Electrohydrodynamic Printing Technology Open

Luyao Zhao, Huifang Liu, Xutao Mei, Xiaoge Yin, Tiancheng Feng , et al. · 2024

Magnetostrictive Bi-Stable Broadband Energy Harvester Based on Flytrap Bionic Mechanism Open

Huifang Liu, Jiaqi Ma, Luyao Zhao, Linru Wei, Wencheng Li , et al. · 2024

A One-Step Fabrication Method of Flexible Magnetostrictive Fiber Ribbon Based on Fe50co50 Alloy and its Characteristics Study Open

Huifang Liu, Luyao Zhao, Wanzhe Wang, Teng Ren, Yunlong Chang , et al. · 2024

Study on microstructure characterization and mechanical properties of AISI 444 Ferritic Stainless Steel Joint by high frequency pulse K-TIG welding Open

Zhihai Dong, Ye Tian, Tingting Hao, Yiwen Li, Junyan Miu , et al. · 2023

In this study, high frequency pulse K-TIG was used to weld AISI 444 ferritic stainless steel (FSS) with a thickness of 6 mm, and the welding process window was determined, and complete penetration was achieved in the state of single pass a…

Achieving a Strong Friction‐Lap Joint of Continuous Carbon‐Fiber‐Reinforced Plastic/Aluminum Alloy via a Surface Laser‐Processing Pretreatment Open

Chunyang Jiang, L.H. Wu, F.C. Liu, Peng Xue, Bolv Xiao , et al. · 2023

In article number 2300034, Lihui Wu, Dingrui Ni, and co-workers employ a laser processing pretreatment to enhance the joining of aluminum alloy and carbon fiber-reinforced plastic (CFRP). The processed Al with porous rough surfaces is tigh…

Study on Determination and Prediction Method of ultra-micro-volume Adhesive Droplet Volume Parametres Open

Dingrui Zhao, Huifang Liu, Xi Chen, Yunlong Chang, Xingfu Yu , et al. · 2023

Nowadays, in the actual microelectronic packaging process, the requirements for packaging quality and accuracy are becoming higher and higher. The research and prediction of the corresponding parameters of the transfer droplet according to…

Erratum: “Working characteristics of a magnetostrictive vibration energy harvester for rotating car wheels” [Rev. Sci. Instrum. 93, 055001 (2022)] Open

Huifang Liu, Weiwei Dong, Yunlong Chang, Yifei Gao, Wencheng Li · 2022

On page 4 (Sec.II B) of the original manuscript, 1 the sentence preceding Eq. ( 6), "The electrical energy generated in the magnetic circuit of the system is expressed as," should be "and the magnetic energy generated by the system can be …

Numerical simulation of an external cusp magnetic field on the welding arc Open

Dan Liu, Honglei Zhao, Lei Shi, Yunlong Chang · 2022

A controlled welding arc is an up-and-coming research area for high-efficiency and high-precision wire arc additive manufacturing. This numerical simulation demonstrates that an alternating external cusp magnetic field (ECMF) can compress …

Effect of external magnetic field on morphology and microstructure of wire arc additive manufacture Open

Honglei Zhao, Yiwen Li, Yajie Sun, Zhihai Dong, Huifang Liu , et al. · 2022

The longitudinal magnetic field assisted CMT+P process is used for arc fuse additive manufacturing of aluminum alloy. Analyze the forming and organization properties of additive components. The excitation frequency is 40Hz ~ 70Hz, and the …

Y(III) Ion Migration in AlF3–(Li,Na)F–Y2O3 Molten Salt Open

Tingting Hao, Xu Wang, Zhai Yu-chun, Yunlong Chang · 2022

In this study, three slots containing an anode chamber, a cathode chamber, and a middle pole chamber were designed by applying the Hittorf method, and a two-way coupling model of the flow field and electric field was established using the …

Research Progress of Arc Additive Manufacture Technology Open

Dan Liu, Boyoung Lee, Александр Бабкин, Yunlong Chang · 2021

Additive manufacturing technology is a special processing technology that has developed rapidly in the past 30 years. The materials used are divided into powder and wire. Additive manufacturing technology using wire as the material has the…

The challenges of the inverse problems solution in welding technology: a review and a practice Open

Yunlong Chang, Александр Бабкин, И. А. Бабкин · 2018

Methods for solving the inverse technological problem, which consists in determining the welding parameters by the desired properties of the welded joint, are discussed. The quality criteria of welds have been developed, which can be used …

Corrigendum to “Toward the multiscale nature of stress corrosion cracking” [Nucl. Eng. Technol. 50(1) (2018) 1–17] Open

Xiaolong Liu, Woonggi Hwang, Jaewoong Park, Donghyun Van, Yunlong Chang , et al. · 2018

Toward the multiscale nature of stress corrosion cracking Open

Xiaolong Liu, Woonggi Hwang, Jaewoong Park, Donghyun Van, Yunlong Chang , et al. · 2017

The phenomenon of high frequency confinement on TIG arc in TIG arc welding Open

Yunlong Chang · 2016

Review on joining of advanced materials and dissimilar materials in Harbin Institute of Technology Open

Jun Feng Qu, Yongping Lei, Peng He, Yunlong Chang · 2016

Yunlong Chang YOU? Author Swipe